SSLClient/examples/EthernetMultiHTTPS/EthernetMultiHTTPS.ino

/*
  Multi Domain HTTPS Client

 This sketch connects to a website (http://www.arduino.cc/asciilogo.txt)
 using an Arduino Wiznet Ethernet shield.

 Circuit:
 * Ethernet shield attached to pins 10, 11, 12, 13

 created 18 Dec 2009
 by David A. Mellis
 modified 9 Apr 2012
 by Noah Koontz, based on work by Adrian McEwen and Tom Igoe

 */


  // NOTE: This example REQUIRES the EthernetLarge library.
  // You can get it here: https://github.com/OPEnSLab-OSU/EthernetLarge

#include <SPI.h>
#include <EthernetLarge.h>
#include <SSLClient.h>
#include "trustanchors.h"
// Enter a MAC address for your controller below.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };

// the two domains we want to query
char server1[] = "www.arduino.cc";
char server2[] = "www.cloudflare.com";
// and the queries we want to send to them
char query1[] = "GET /asciilogo.txt HTTP/1.1";
char query2[] = "GET /cdn-cgi/trace HTTP/1.1";

// Set the static IP address to use if the DHCP fails to assign
IPAddress ip(192, 168, 0, 177);
IPAddress myDns(8, 8, 8, 8);

// Choose the analog pin to get semi-random data from for SSL
// Pick a pin that's not connected or attached to a randomish voltage source
const int rand_pin = A5;

// Initialize the SSL client library
// We input an EthernetClient, our trust anchors, and the analog pin
// Additionally specify that we want to store 2 sessions since we are connecting to 2 domains
EthernetClient base_client;
SSLClient client(base_client, TAs, (size_t)TAs_NUM, rand_pin);
// Variables to measure the speed
unsigned long beginMicros, endMicros;
unsigned long byteCount = 0;
bool printWebData = true;  // set to false for better speed measurement

void setup() {
  // You can use Ethernet.init(pin) to configure the CS pin
  Ethernet.init(10);  // Most Arduino shields
  //Ethernet.init(5);   // MKR ETH shield
  //Ethernet.init(0);   // Teensy 2.0
  //Ethernet.init(20);  // Teensy++ 2.0
  //Ethernet.init(15);  // ESP8266 with Adafruit Featherwing Ethernet
  //Ethernet.init(33);  // ESP32 with Adafruit Featherwing Ethernet

  // Open serial communications and wait for port to open:
  Serial.begin(115200);
  while (!Serial) {
    ; // wait for serial port to connect. Needed for native USB port only
  }
  
  // start the Ethernet connection:
  Serial.println("Initialize Ethernet with DHCP:");
  if (Ethernet.begin(mac) == 0) {
    Serial.println("Failed to configure Ethernet using DHCP");
    // Check for Ethernet hardware present
    if (Ethernet.hardwareStatus() == EthernetNoHardware) {
      Serial.println("Ethernet shield was not found.  Sorry, can't run without hardware. :(");
      while (true) {
        delay(1); // do nothing, no point running without Ethernet hardware
      }
    }
    if (Ethernet.linkStatus() == LinkOFF) {
      Serial.println("Ethernet cable is not connected.");
    }
    // try to congifure using IP address instead of DHCP:
    Ethernet.begin(mac, ip, myDns);
  } else {
    Serial.print("  DHCP assigned IP ");
    Serial.println(Ethernet.localIP());
  }
  // give the Ethernet shield a second to initialize:
  delay(2000);
  // connect!
  connectSSL();
}

void loop() {
  // if there are incoming bytes available
  // from the server, read them and print them:
  int len = client.available();
  if (len > 0) {
    byte buffer[80];
    if (len > 80) len = 80;
    client.read(buffer, len);
    if (printWebData) {
      Serial.write(buffer, len); // show in the serial monitor (slows some boards)
    }
    byteCount = byteCount + len;
  }

  // if the server's disconnected, stop the client:
  if (!client.connected()) {
    endMicros = micros();
    Serial.println();
    Serial.println("disconnecting.");
    client.stop();
    Serial.print("Received ");
    Serial.print(byteCount);
    Serial.print(" bytes in ");
    float seconds = (float)(endMicros - beginMicros) / 1000000.0;
    Serial.print(seconds, 4);
    float rate = (float)byteCount / seconds / 1000.0;
    Serial.print(", rate = ");
    Serial.print(rate);
    Serial.print(" kbytes/second");
    Serial.println();

    //quick delay
    delay(1000);
    // connect again!
    connectSSL();
  }
}

bool r = false;

void connectSSL() {
  // cycle the server we want to connect to back and forth
  char* server;
  if (r) server = server1;
  else server = server2;
  r = !r;
  
  Serial.print("connecting to ");
  Serial.print(server);
  Serial.println("...");

  // if you get a connection, report back via serial:
  auto start = millis();
  if (client.connect(server, 443)) {
    auto time = millis() - start;
    Serial.print("Took: ");
    Serial.println(time);
    // Make a HTTP request:
    if (server == server1) client.println(query1);
    else client.println(query2);
    client.println("User-Agent: SSLClientOverEthernet");
    client.print("Host: ");
    client.println(server);
    client.println("Connection: close");
    client.println();
    client.flush();
  } else {
    // if you didn't get a connection to the server:
    Serial.println("connection failed");
  }
  beginMicros = micros();
}